Swells
- Turn off power to your modular system.
- Connect a USB cable from the rear of the module to your computer.
- Hold down the BOOT button on the rear of the module and turn on power to your modular system. Note: The LEDs will not light up when in bootloader mode.
1.2.6.0 (2026-08-13)
- Fixed: Issue causing noise with some trim settings.
1.2.5.0 (2026-07-25)
- Tweak: Smoother/Finer Control handling.
1.2.0.0 (2026-06-05)
- New: Increased gain on Wet output for all Models — Better matched across Models and compared to Dry signal.
- New: Adjustments to DAMP Hi/Lo Frequency Ranges for all Models — Allow for more dramatic play and modulation.
- New: Reduced minimum SIZE for X1/X2/Y1 - Really fun for resonator/chorus type sounds.
- Tweak: Increased Compressor Makeup Gain on Lofi:MIN/MAX for Bank Y.
- Tweak: Reduced minimum HPF>VERB frequency from 50Hz to 10Hz.
- Fixes: Minor bug fixes, optimizations, and tweaks.
1.1.0.11 Beta (1.2RC) (2026-05-22)
- New: Increased gain on Wet output for all Models — Better matched across Models and compared to Dry signal.
- New: Adjustments to DAMP Hi/Lo Frequency Ranges for all Models — Allow for more dramatic play and modulation.
- Tweak: Reduced minimum SIZE for X1/X2/Y1 - Really fun for resonator/chorus type sounds.
- Tweak: Increased Compressor Makeup Gain on Lofi:MIN/MAX for Bank Y.
- Tweak: Reduced minimum HPF>VERB frequency from 50Hz to 20Hz.
- Fixes: Minor bug fixes, optimizations, and tweaks.
1.1.0.7 Beta (2026-05-19)
- Fixed: Regression in 1.1.0.6 that muted X3 Output.
1.1.0.6 Beta (2026-05-15)
- Tweak: Gain increases on all Models.
- Tweak: Gain adjustmens on Drive and Freeze options.
- Fixes: Minor bug fixes, optimizations, and tweaks.
1.1.0.0 (2026-04-27)
- New: Verb Kill Burst mode (YELLOW) — Kills the Verb output and decay while BURST is active.
- New: Show incoming sync pulse (divided rate) on the REVERSE LED when Reverse Sync is enabled.
- New: The audio buffers will clear when switching between Models, old behaviour can be enabled with a system boot toggle, see manual for details.
- New: Idle Timeout for Alt/Trig pages, they will return to the main display after 20 sec of inactivity.
- Tweak: New ALT Parameter display to allow for activity display while adjusting ALT Parameters—
- TRIM shown on INPUT-LEVEL LED
- EF GAIN shown on INPUT Activity LED
- LPF→EF shown on MIX Activity LED
- HPF→VERB shown on MIX-LEVEL LED
- Tweak: Improved Swell RISE/FALL Transitions.
- Tweak: Improved Swell One Shot/Delayed One Shot/Looper signal handling.
- Fixed: THRESH knob now works on the Alt page.
- Fixed: LPF→EF behaviours.
- Fixed: Trigger behaviour on One Shot Swell mode (GREEN).
- Fixed: X3 audio glitches when FLOW was set to max.
- Fixes: Minor bug fixes, optimizations, and tweaks.
- Updated manual available at intellijel.com/support.
1.0.9.0 (2026-04-09)
- Fixed: Knob values for the primary and ALT function should no longer affect each other when switching to the ALT page.
- Fixed: Input Activity LED now reflects post-INPUT (aka Pre-Verb) control when not on ALT page.
- Fixed: Advanced CV Assign regression in 1.0.7.0.
- Tweak: Adjustments to compressor settings for LO-FI MIN/MAX on MODEL Bank Y.
- Fixes: Minor bug fixes, optimizations, and tweaks.
1.0.0.0